I don't have a farm but I do live on a rural acreage. I had a new fence built and one of the places I had the fence replaced was around the lagoon. The lagoon had the only fence that was actually page wire, the rest was just a 5 wire fence. To deal with the page wire I got a cordless angle grinder and a box of zip cuts and cut it up into 6 foot sections which would fit into the box on my truck. It had an 8 foot box but 6 foot pieces of page wire are easier to handle. The whole job took half the time it would have if I had chopped it up with my bolt cutter. I still have most of the zip cuts.Battery powered tools, around the farm they are indispensable. On sat we were doing some work on a calf shelter, had the drill, sawsall. sidegrinder and impact driver in use.
We had one of those w/ our old Forney. I struck an arc w/ it a few times just to see what it would do. Never actually used it for anything.I think it was an old Fourny book I found had a number of things an electric welder could be used to do, a couple of carbon rods in the “special holder” for heating stuff. The holder held the rods and a pivoting toggle allowed one rod to be moved closer to the other to maintain a slight distance between them. Could be used to heat for cutting, bending, soldering, possibly brazing.
I need to have a look, might still have the book. It was full of possibilities for a 10-11 year old!
dont know about the tig rod, but my entry into silicon bronze went through my mig welder, outcome was better than expected!!Not as entertaining, but I get a lot of use out of silicone bronze filler rod, at work and home. Tig brazing, torch brazing, and it holds a point well as a pick/probe when you don't want to chew up steel or iron parts, handy stuff.
I bought the M12 one. Really handy while putting on these crash bars.
Did you get one?Apparently Milwaukee has a new line of M12 Extended Reach Rachet Wrenches. You can get 1/4, 3/8, and 1/2" drives. Very cool!
![]()
M12 FUEL 1/2" Extended Reach Ratchet | Milwaukee Tool
Experience unmatched power and comfort with the M12 FUEL™ 1/2" Extended Reach Ratchet—your solution for tough jobs.www.milwaukeetool.ca
Did you get one?
I had been told that using an impact wrench on big threading taps was the way to go with a guy repairing a D6. I thought yeah, right, that'll shatter them fast enough.
So yesterday for the first time I had 22 holes to tap at 1/4x28 for grease nipples. I got brave and drove the tap wrench with my Milwaukee impact driver with a adapter to 3/8.
Wow.
I'm going to buy a set of those tap sockets at Princess on Wednesday.
Hi,Just seeing this thread for the first time. Never heard of tap sockets. Seem like both a great idea - and an excellent way to break more taps faster.
It's kind of like parting. Slow speed and gentle feed is the usual advice, but let er rip works better.Just seeing this thread for the first time. Never heard of tap sockets. Seem like both a great idea - and an excellent way to break more taps faster.
Agreed, how you start a tap is critical. The ratchet isn't impact, gives you a pretty good feel. Using a tapping block would help prevent a crooked startDepends on power source, right? If a power tool, sure. But a socket wrench would make going off-axis so much easier.
Never heard of tap sockets. Seem like both a great idea - and an excellent way to break more taps faster.
The ratchet isn't impact, gives you a pretty good feel. Using a tapping block would help prevent a crooked start
But a socket wrench would make going off-axis so much easier.



A 9/32 socket head screw😀
M9 SHCS (while hex head, not SHCS, my tilting table lock screws are M9, so they do exist).What do you use a 7mm allen wrench for?