Just Joined

[Stainless201]

Hi everyone, I have an XLO 602 with the original paperwork I bought years ago. I found out it had a repair to the overhead gearbox which was the small gear ( originally made of bronze), this one is steel . It has blue dye on it so it's been replaced ??? The gear seems slightly not right, almost a tight spot I tried to measure or the hole center is out . I finally am retired & have more time to fix stuff. I am looking to buy that gear if anyone knows where I could find one is the best option, if not available does anyone have the correct dimensions, material, pictures etc, so I can try to have one made. I forgot to mention the gear noise changes from a clacking noise unloaded to fairly quiet noise loaded . Thanks very much, glad I joined the group & look forward to hearing back from all the experience on this site. Ron.

 

[YYCHM]

Welcome from Calgary.

 

[Stainless201]

Hi Craig, thanks

 

[YYCHM]

Hi Craig, thanks

Where are you located? @LenVW should be able to help you source XLO parts.

 

[Stainless201]

I. am in Hamilton Ontario

 

[Proxule]

Welcome, Loaded gears can and do sound different, especially if too much backlash exists they will slap around.
The tight spot as it rotates does indeed worry me. I do not have specs or dimensions for your gear, but others might. Perhaps even a source for the gear!

Enjoy your stay!

 

[Dusty]

Welcome aboard from sunny Saskatchewan. Born in Hamilton, raised and educated in Stoney Creek.

 

[Stainless201]

Welcome, Loaded gears can and do sound different, especially if too much backlash exists they will slap around.
The tight spot as it rotates does indeed worry me. I do not have specs or dimensions for your gear, but others might. Perhaps even a source for the gear!

Enjoy your sta

Welcome aboard from sunny Saskatchewan. Born in Hamilton, raised and educated in Stoney Creek.

Thanks neighbour

 

[Stainless201]

Welcome, Loaded gears can and do sound different, especially if too much backlash exists they will slap around.
The tight spot as it rotates does indeed worry me. I do not have specs or dimensions for your gear, but others might. Perhaps even a source for the gear!

Enjoy your stay!

Thanks,

 

[YotaBota]

Welcome from the west coast.

 

[Bandit]

Welcome from south of Calgary

 

[thestelster]

@Stainless201 Hi Ron check this post:

Excello 602 Power Feed Repair

I decided that I wanted to fix the power feed on my Excello 602. The 602 have a power feed mounted on the knee which is basically a DC servo motor and a speed controller. The servo is constantly turning and when the lever on the saddle is engaged, a spline shaft is engaged that connect to the...

canadianhobbymetalworkers.com

 

[Stainless201]

Welcome from the west coast.

Thanks

 

[Stainless201]

@Stainless201 Hi Ron check this post:

Thanks, I will try that number tomorrow !

 

[DavidR8]

Welcome aboard from Victoria.

 

[Stainless201]

Welcome from south of Calgary

Thanks, great name !

 

[whydontu]

Welcome from Vancouver!

 

[Stainless201]

Welcome from Vancouver!

Thanks

 

[Stainless201]

Welcome from the west coast.

Thanks

 

[LenVW]

Hi Craig, thanks

I. am in Hamilton Ontario

I. am in Hamilton Ontario

Hey Ron,
Welcome to this group.
I apprenticed at . . . Ex-Cell-O Special Tools Division
You can try Roy (below) he has a shop called ‘Preston Rebuilt Machinery’ in Cambridge.
He used to repair a lot of the 602s in the area, but, recently has focused more on FIRST mills.
He may still have some inventory of XLO parts.

Roy Weidinger - Preston Rebuilt Machinery
385 Dundas Street, Unit 6D
Cambridge, Ontario
(519) 621-4258