• Hi - We're having intermittent forum issues. Posts, alerts, and anything involving email like signing up or password changes are having problems but not for everyone or everywhere. Josh is working on it. No ETA right now. Thanks Josh - BTW this is a volunteer forum so SLA's are just best effort. EDIT -> I manually batch updated about 25 people stuck on the email notification. Try logging in now with your password. EDIT -> May 8/23. I updated another bunch of users stuck on email notifications. Try to login if you are stuck. If you really can't get in contact us on facebook or if you know a forum member get them to ask us.
  • [Ad-Free Experience]
    Register Today, Craft a Post, and Enjoy an No-Advertising Experience.
    Click Here to Register

Removing a Mt1 taper from a No3 jacobs chuck

C

calgaryguy

Chris
Picked up a 17/32 Jacobs chuck (seller scammed me into thinking it was a 3/4") for $50.

It has what I think is an mt1 taper in it right now. I've tried heating the chuck with map gas torch and then trying to twist/pull the taper out, but havent gone very far as I dont want to damage the chuck.

There is no place to use chuck removal wedges.

Thoughts on how I might get this Mt1 taper out?

IMG_2881.JPG IMG_2882.JPG IMG_2883.JPG
 
thestelster

thestelster

Ultra Member
Premium Member
YYCHM said:
I just checked my Jacobs chuck and the taper hole is blind. Wedges are required to remove the taper.
Click to expand...
I guess, there are quite a few variations. I switched arbors on my ball bearing Jacobs a couple days ago. Removed the old one with the wedges, and noticed that the chuck had a through hole.
 
P

PeterT

Ultra Member
Premium Member
This method shows a hydraulic press pushing on the end with a pin. Maybe some penetrating miracle juice in the joint would help.

How To: Remove a Jacobs chuck arbor

I recently bought a Jacobs #18N 3/4" chuck with a #4 Morse Taper arbor. For my application I'll need to use the chuck with both the existing #4 Morse Taper arbor and a 3/4" straight shank arbor. Here's the chuck when I bought it with a #4 Morse Taper arbor installed. The smaller chuck to the...
www.garagejournal.com www.garagejournal.com
 
Proxule

Proxule

Super User
Mounted and dismounted many a chucks, all I have seen or serviced was pressed out from the center, There should be a hole to slip in a small dowel or shoulder bolt or pin or what ever, Press away.
 
C

calgaryguy

Chris
Proxule said:
Mounted and dismounted many a chucks, all I have seen or serviced was pressed out from the center, There should be a hole to slip in a small dowel or shoulder bolt or pin or what ever, Press away.
Click to expand...
There was no hole. I had to drill one. I'll post pics of the 'after' once the chuck comes out of its evaporust bath tomorrow

This is a 'old' Jacobs No3 chuck I think, marked 'made in Sheffield England' - maybe its age makes it different.
 
Proxule

Proxule

Super User
calgaryguy said:
@RobinHood I drilled a 5/16" hole in the bottom of the chuck and the taper popped out with a couple of hits with a hammer and a brass punch after 30 seconds of map gas pre-heat. Thanks!

I'll post a pic later as I immediately put the chuck in an evaporust bath.
Click to expand...
Consider electrolysis next time. Its amazing!
 
C

calgaryguy

Chris
Proxule said:
Consider electrolysis next time. Its amazing!
Click to expand...
I've been pretty happy with Evaporust tbh. Its simple, I dont worry about gas in the shop, no charger plugged in, etc. Warming the evaporust a bit really makes it work well.

I have considered electrolysis for larger parts/projects. I havent had a need yet however.
 
Proxule

Proxule

Super User
calgaryguy said:
I've been pretty happy with Evaporust tbh. Its simple, I dont worry about gas in the shop, no charger plugged in, etc. Warming the evaporust a bit really makes it work well.

I have considered electrolysis for larger parts/projects. I havent had a need yet however.
Click to expand...
Fair enough, It is indeed more work. But the result and speed is not comparable. 25L pail of water takes about half a cup more or less of washing soda, And a sacrificial anode. ( steel ). The real beauty is the speed it does the cleaning at. And that the slightly caustic solution strips grease oil paint etc etc.

If you need to buy the charger and other supporting equipment, Evaporust is the way to go. Especially if its small.

Just my 2 cents.
gluck
 
Doggggboy

Doggggboy

Ultra Member
calgaryguy said:
I've been pretty happy with Evaporust tbh. Its simple, I dont worry about gas in the shop, no charger plugged in, etc. Warming the evaporust a bit really makes it work well.

I have considered electrolysis for larger parts/projects. I havent had a need yet however.
Click to expand...
I bought a 20 litre pail. I expect to be dead before I need to replace it and I can just drop a part in the pail as opposed to finding a tub the right size, covering the part and then funneling it back into the container when done. 200 bucks at Tenaquip with free Canada Post shipping. About the same price as buying 4 litre jugs at PA but much handier.
 
Last edited:
You must log in or register to reply here.
Top