• Scam Alert. Members are reminded to NOT send money to buy anything. Don't buy things remote and have it shipped - go get it yourself, pay in person, and take your equipment with you. Scammers have burned people on this forum. Urgency, secrecy, excuses, selling for friend, newish members, FUD, are RED FLAGS. A video conference call is not adequate assurance. Face to face interactions are required. Please report suspicions to the forum admins. Stay Safe - anyone can get scammed.

Flaring Tool Kit

jcdammeyer

John
Premium Member
A friend has this sort of irrigation valve setup for water out to the water distribution valves.

1795309458689.png


Looks to be a 3/8" flared copper fitting.

1795309926323.png
When I did my compressor system I used 1/2" copper and a flaring tool borrowed from the Chris MacKay. He's no longer with us so I need to look at replacing my 50 year old broken flaring system.

I think what he had was this:

and I machined up a couple of special dies to fit whatever wasn't in the kit. But don't really remember anymore.

Anyway, he wants to connect that fitting to this so he connect his air hose to blow the water out to prevent pipes freezing during the winter.

1795309961930.png

Once I have 1/2" copper tube going to that will be easy enough. But since my flaring tool is broken and I need to replace it I'm looking for suggestions.
Thanks
 
That clamp looks like a battery post or windshield wiper remover puller, it doesn't look from here like that would work with your setup?
It's missing the 45 degree anvil which is why it looks wrong That fell off. I think I made a new one on the lathe for it but can't find it.

Then I found a different one and took a stab at some 1/4" tubing. Seemed to come out alright. After that some bending, lathe work to adapt the NPT inside to take the 1/4" tube. Solder and assemble.

AdaptorDone.jpg
 
Almost 3 years ago I bought this kit from Amazon. I didn't remember sending it back so I spent a while looking for it. It was trash. It's no longer available from Amazon. The Kit that Chris MacKay loaned me was so much nicer.
1795335758121.png


Edit: Should have added that I did end up returning it to Amazon because it was garbage.
 
Last edited:
IIRC CT has their "loan-a-tool" program and there is/was a flaring kit available.

@jcdammeyer - How's the knee?
Slowly getting better. Entire leg is still swollen. The two needle marks from the anaesthetic and the one that drew out over 50ml of fluid are still visible. There's also bruising and sensitivity in an area that doesn't make sense since I don't remember ever banging the knee.
X-Ray results should be available tomorrow. Still no idea if it was Gout, Pseudogout or Osteoporosis or maybe I banged it and didn't know.
Meanwhile I have to force myself to sit and keep the knee elevated. Hard to do when there are all these projects that involve standing in front of a lathe or mill or robot arm.
 
Some time ago, I was working on some brake lines, ended up getting 3? different kits to try and put flares on some lines. Could not get a proper flare with any of them, the belling was off on all of them. The flare would be off center from the tube and of course the nut would not go over the flare. The flare would be longer on one side than the other.
A number of words were used to no effect. Ended up using the crane from a very old set as it was found that the cranes from the new sets were all pushing slightly side ways and making the flare larger on one side. This may not have been as pronounced with copper tube which required less force to form then steel tube. It seemed a number of mismachined part tolerances added up to making crap.
As the sets had been purchased from different stores, all the sets seemed to be different, and were not cross compatible, or produced the same result. The old set did not work with the tube, as the clamping bars could not hold the steel tube without slipping, likely many hundred of uses causing wear or perhaps a difference of wall thickness from slightly varying specifications over a long time.
Hope the knee improves quickly.
 
Back
Top